Crop Updates: A great deal of timely information was provided in this week’s CropWatch at http://cropwatch.unl.edu including information about high heat and pollination, applying fertilizer during pollination, western bean cutworm scouting, forecasted yields, etc. Please check it out!
Several called me asking about applying fertilizer during pollination. I shared that while
I wasn’t aware of research, I personally was concerned about anything potentially interfering with pollination and that I do recommend 30 lbs of N at brown silk if needed or if you were originally planning split nitrogen apps. This is based on research from Purdue sharing today’s hybrids use 30-40% of their total Nitrogen from flowering through maturity. After discussing with Dr. Tom Hoegemeyer, Adjunct UNL Professor of Practice, he offered the following insights: “Pollination mostly occurs between 8:30 a.m. and Noon. Thus, as a precaution, I would not run a pivot on pollinating corn from 6 a.m. to Noon. When the temperature is 90°F to 95°F, the pollen is killed by heat and is seldom viable past 2 p.m. That leaves lots of time to run pivots, apply N, etc. when it won’t harm pollination. Silks tend to be viable for three or four days at these temperatures, so if a plant isn’t pollinated one day, generally the next day will work just fine. (If nitrogen is needed), I’d recommend that nitrogen go on as soon as practical. Corn nitrogen use is very high during the pre-tassel growth phase and again at kernel growth, from one to three weeks post pollination. About seven to ten days post pollination (before brown silk) lower N will start causing kernel abortion and serious yield loss in corn.” The UNL recommendation for fertigation is to use 30 lb of N with 0.25″ of water or 50-60 lb of N with 0.50″ of water.
Last week also brought questions regarding thresholds and difficulty in finding Western Bean Cutworm egg masses with moth flights at their peak. You can view light trap data from UNL’s South Central Ag Lab thanks to Terry Devries at: https://scal.unl.edu/ltr2018.pdf. There’s also a great article in this week’s CropWatch on how to scout for them, insecticide options, and additional recommendations. Thresholds for western bean cutworm are 5-8% of corn plants in the field containing egg masses or larvae. Egg masses can be difficult to find during pollination with pollen hiding them. ‘Typically’ egg masses are found in the top third of the plant on the upper sides of leaves and near midribs or leaf axils. However, with higher heat, I tend to find them closer to the ears and have even seen masses laid on the ear husks and on the backsides of leaves (not common). While larvae are generally known to move up the plant to feed at the tassels, I’ve seen high heat force larvae into ears earlier. It typically takes 5-7 days for larvae to hatch and the egg masses turn purple just prior to hatching. A number of insecticide options are available for both aerial application and via chemigation; these products are listed in the CropWatch article.
With insecticide applications occurring in corn for both western bean cutworm and also corn rootworm beetles, many have also called or talked with me about the recommendation of fungicide applications. Right now, I haven’t found gray leaf spot above 3 leaves below the ear leaf in several counties. There’s been some mis-diagnosing bacterial leaf streak as gray leaf spot. Southern rust was just confirmed in a Kansas county this week, but we still have yet to confirm it in Nebraska. Even the longest residual products won’t get us through August if a fungicide application occurs now. I can appreciate that economics are tight so the thought is to save an additional application cost by applying a fungicide now with the insecticide. And, I can appreciate economics are tight regarding why apply a fungicide right now when disease pressure doesn’t warrant it? Perhaps, at least those of you with the ability to chemigate could consider waiting till disease pressure warrants it for your field, if it does. Always in the back of my mind is the need for late-season protection with southern rust eventually showing up and gray leaf spot often worse then.
My perspective is from a resistance management and research-based one. We have 5 total modes of action for fungicides with 2 of them being in nearly every fungicide product we use in corn, soybean, and wheat because they work against foliar fungal pathogens. At some point, our pathogens will also adapt, as we’ve seen our weeds and insects do…it would be like losing our ability to control gray leaf spot and southern rust similar to palmer amaranth on the weed side. In Nebraska, Dr. Tamra Jackson-Ziem’s research has not shown an automatic yield increase to fungicide application in the absence of disease. And, it has also not shown an automatic yield increase when applied at tassel. In a high heat and low disease year like 2012, there were no statistical yield differences with fungicide application vs. the untreated control. Even in years with some disease pressure such as 2008-2010, she found no statistical yield differences between when various products were applied from Tassel through Dough stages. In high disease years, her research shows the benefit of fungicide application for reduced disease pressure and increased stalk strength. Fungicides are great tools to help us with disease pressure and stalk strength. Just would encourage all of us to consider when we really need to apply them and to understand that research in Nebraska does not automatically show increased yields with the use of them or with the timing of Tassel/Silking vs. later in the year. Also, hybrids may vary in their response due to disease susceptibility and other factors. Not all her data is listed at this site, but you can view it for yourself at: https://go.unl.edu/ni3y.
Bagworms: I’ve been seeing shelter belts and various trees turning brown from heavy
bagworm infestations. Please be checking your trees if you are noticing them turning brown. Additional information can be found at: https://go.unl.edu/rgju.
Posted on July 15, 2018, in Crop Updates, Diseases, Insects, JenREES Columns and tagged bagworms, corn pollination, fertigation, fungicide application, western bean cutworm. Bookmark the permalink. Leave a comment.